Welcome to the Cave Diver's Forum.
+ Reply to Thread
Results 1 to 5 of 5
  1. #1

    Default Compressor Questions - High Pressure Steel Tubing 1/4"

    This post is for any compressor owners that have ran any high pressure stainless steel tubing from their compressor to say a cascade block or a pressure switch, then into a cascade block.

    My questions are:
    what was the tubing manufactor?
    were you able to source the fittings to connect to your compressor?
    what is the pressure rating?
    were you able to use a standard pipe bender to bend it? or did you use 45/90 to change the direction?

    I did locate this company that offers high pressure tubing, its way overkill (150K PSI) but it would work as long as I can source the fittings.

    http://www.autoclave.com/products/fi...re_tubing.html


  2. #2
    Member
    Join Date
    Oct 2004
    Location
    Right on the Ragged Edge
    Posts
    3,133

    Default

    Look over the swagelok or Parker websites. Both have fittings and tubing. You can bend small tubing with a bender.

    "Ain't nothin' an ol' man can do but bring me a message from a young one."
    "Anytime you see me with my arms around an old man, I'm holding him for the police."
    "My husband was so ugly, he used to stand outside the doctor?s office and make people sick."
    "They say you shouldn't say nothin' about the dead unless it's good. He's dead. Good! "

    Moms Mabley 5-23-75


    "Into the blue again; in the silent water
    Under the rocks, and stones; there is water underground" Talking Heads

  3. #3
    Member
    Join Date
    Oct 2004
    Location
    Bloomington, Minnesota
    Posts
    133

    Default

    I have ordered from these people before https://www.augustindustries.com/

    Al


  4. #4
    Member
    Join Date
    Jun 2011
    Location
    St Petersburg, FL
    Posts
    2,684

    Default

    I chose to just go with custom HP hoses that I got from Aplus Marine. SS is pretty and convenient, but it can take some trial and error to make your bends and setup pretty, and it can get very expensive. Not only do you need the tubing, but you need the bending set, all the bits and pieces like ferules and whatnot. It can get overwhelming and expensive.


  5. #5

    Default

    You can check our website www.nuvair.com

    We have all of the fittings you would need and tubing.

    Yes, it is nice to be able to bend the tubing into a proper shape. And, yes it takes the right tools, a bit of skill, and practice to make it look good. And always, bent elbows are best. But, it is possible to just cut straight sections and piece them together with fittings.



 

Similar Threads

  1. Personal Compressor Questions
    By Benderr in forum Gear, Equipment & Tools for Cave Diving
    Replies: 5
    Last Post: 08-01-2017, 08:10 AM
  2. FS High pressure regulator
    By amphipod06 in forum Gear Exchange
    Replies: 2
    Last Post: 06-05-2013, 07:32 AM
  3. Al 80 "Neutral buoyant" 3300 psi working pressure
    By jmaddox in forum Gear, Equipment & Tools for Cave Diving
    Replies: 16
    Last Post: 04-13-2010, 09:45 AM
  4. Madison Blue "The Pressure Gauge"
    By Cave Ranger in forum Main Forum
    Replies: 6
    Last Post: 11-15-2007, 10:08 PM
  5. FS- High Pressure Doubles
    By connielore in forum Gear Exchange
    Replies: 0
    Last Post: 09-09-2005, 08:32 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts